Search results

do you have any covers for the Laredo black /sliver combo high bucket , I have seen some new ones but price has been out of my reach

head is a 3933002 which is a 258 4.2 86-87 block which use 1/2" head bolts I believe block 3213867 is 72 to 74 and was on a 232 and the 258 this link has some info http://www.enginepartswarehouse.com/enginecatalog/AMERICANMOTORS.PDF but I am not sure whats involved to do the swap

this is for a stat 800 series

\ I think that the relay or flasher was built in but I am not positive as it has been years since I worked on one but there is a flasher somewhere else as I found a few links online showing the flasher and maybe it will help here are the links http://www.cj3apage.com/wiring%20diagrams.htm and...

well i wish u luck and hopefully it comes out smooth , have u determined were it was leaking ? if it was the master cylinder I would try changing that before pulling , and see if that works , if the slave cylinder is leaking then I guess u gotta pull it if its internal slave either way I hope...

has your turn signal switch been replaced or is it an old one ? I believe on those old 52's that the flasher is build in with the turn signal switch to the best of of my knowledge which at my age is fading fast ,,,and make sure you have the right bulbs , have seen people use the wrong bulb and...

it goes on

if the pedal is not getting weak but just not letting you get it in gear properly it is possible that it is the flywheel if it has been resurfaced to many times but I do not know the tolerances and that is if the clutch and pressure plate are new and installed properly then maybe flywheel...

well are you getting air out every time you bleed the system or is it pure fluid ? if its pure fluid then you probably have a problem in the system , you may need a new clutch master cylinder or slave cylinder , its easy enough to change the clutch master cylinder and bleed the system but you...

is the slave cylinder new ? and how old is the clutch ? I installed a new clutch once but used the original flywheel and caused a problem like yours,, the flywheel was worn to much and can only be resurfaced once or twice untill it needs replaced as they aren't designed beyond that point , I...

sounds more like there is still air in the system , did the brakes work before the bleeding and flush of the system ? usually the booster makes it hard to push the pedal , the master cylinder could have air still trapped , how did you bleed the system ? when bleeding the reservoir must be...

yes this is the best thing to do if all this is a new problem , bad bulbs and grounds in the sockets can screw everything up , and then check the headlight switch and flashers , dimmer switch is something to check as well but get all the bulbs and sockets first and you may be good to go

I agree about buying a complete set and the hood hinge bolts are not as bad to get out but you do need good bits , dont buy a cheap set

looks like nice work

its possible your were dealing with a weak ground , if I were you I would clean more of the grounding points like battery cables on both ends and any other areas related to it,,you might be lucky and it was just a ground issue as this can cause similar problems as you described , I hope that was...

I am looking for a good quality padding for my 84 cj7 roll bar , the original was nice and smooth an thick cushion padding made out black denim what I bought from jc whitney and have seen at summit and others is thin and keeps a wrinkled look made out of black denim does anyone sell the...

have heard maybe computer can do this,,try this from post I have read turn the key on untill all dash lights function normally and then see if it will crank an start , after it warms up it may start easily , I have read that the capacitors fail in the computer untill warm and this could be...

yea the 84 was the first year that the cj7 had the AMC 150/2.5 the earlier like 69jeepcj mentioned would have the iron duke

I would first clean the throttle body and egr valve and any components around the throttle body with some carb cleaner and clean out any carbon build up in the areas and see if that helps

you can post pictures with the post , I didnt have any problems