Search results

1072233 I think that if you have the time, you mite as well drop your gas tank and check it for rust, holes, etc.. change new bolts and stuff, its not that hard... good luck...[addsig]

1072659 check your rpm's sometimes too low will not give enough cooling power to the radiator, and not enough pump flow, it shoud be around 700, I agree on the thermostat, put it back in... good luck.[addsig]

1074612 since Ive never been in a TJ i cant realy say much about it, but I agree, older and tuffer is better, id love for my YJ to have a CJ dashboard, those things are borderline classic jaguar sports car cool... , but I still like my YJ better on the outside...[addsig]

1074735 I grinded a 3/8 extention till it fitted and had no problem... but refilling the trany was the trouble, had to buy an oil pump for $5... going to change it again soon , can anyone suggest a oil grade and brand???[addsig]

1073607 Hi, I was wondering, how much are you spending on the gear swap?? couse Im going the same path you are in the future...[addsig]

1073612 don't think you will have much truble with that, I did a 3" lift and had to bend the shifter, weld an extention to the trany shifter, and the gas fill hoses were left behind, i have to remove the cap from under the jeep every time I refuel, no problems with the bakes at all, and...

1073778 I think im goig to wait for the 4 cyl YJ jeep axels...Thanks four your help...[addsig]

1043312 I just decided remove the trany and pay a visit to my clutch and it turn's out that the clutch pilot bearing was totaly destroyed (go figure) the only thing left was the outer ring, but it wont cum out, i've tried extractors, hamers, hidrolic tecnics, etc, but nothings worked, Im...

1043444 I just reacently changed the clutch on my jeep and a very weard shake has developed, every time I get a green lite (after stoping) , the jeep shakes for a second and then it takes off, like it slips or something( its kinda like I was new to driving manual transmition) after that its all...

1044147 I, i've gone from a perfectly awesom 88'XJ to my newly acuired YJ ive had it for 2 weeks and in that time ive changed the clutch, power stearing punp, rear track bar axel braket, tuned it up, prepeared it for winter and gave it a good wheather protectent undernith, now I want to rebuild...

1048233 Hi, mi name is geronimo, I live in Mexico, I have a 88 Yj with a 4.2L, manual trans, that has some mods, starting with msd ingniton 6AL, Blaster 2 Coil, Tach Adapter 8910, no cat, and recently changed the timing set, and carburator for a Carter 2 Barrel that I got in a junkyard in very...

1066670 I reacentoy changed the preasure sending unit becouse the last one would not send a signal, but the new one send's minimum 40psi of preasure that's at idle and the jeep fully warmed up. Is there something as to much preassure... :-? , or is there somthing stuck inside?? o what....[addsig]

1067116 Can somebody tell me the importance of the rear track bar?, since I got my jeep the rear track bar bracket on the axel was totaly destroyed ive welded it back on but it just keeps on braking (do I suck at welding o what :-P). sow I decided to take the hole thing off, the cuestion is...

1067223 Here's a dumb cuestion, how hard is it to swap the pinion and the ring from a cherokee to a wrangler for the dana 35 and 30 diffs. couse i want to go from a 3.something to the 4.10, :-) you could say im very mecanicaly inclined but that swap kinda intimidates me a little couse ive...

1068328 Hi, i was wondering, do i have to change the R&P on the 2 axels when i do a swap or can i just change the rear one, from a 3.31 to a 4.11?? Thanks for the help... :-? [addsig]

1071582 Hi, I have a 88 Yj with stock 3.07 gears and when I put in 31" the engine lost most of its performance. Sow I am very interested in swaping my gears to 4.11 at the least. Sow I shoped arround and found a shop that would rebuild my axels (bearings, seals, etc..), use used R&P and, and...

1073611 Hi, after loking in almoust every junkyard I now, I found an old '86 XJ with 3.73 gears, my jeep has 3.07 and Im running 31" with the 258, and I with that gearing ive lost the performance it had, sow I was wondering , will the gears and cases fit into my diferentials, or are they not...

1073780 has anyone installed a crane cams power max camshaft?, im going to shange my lifter couse they are all tappy, and I mite as well add some performance, but will I get it from this camshaft???[addsig]