Search results

not to sound way off but I love my goodyear MT/Rs they have nice shoulder lugs not compared to a bogger but they hang with my buddys swampers on his Ranger and are a lot more square for more surface contact on the road and not too noisy unless it cold then they roar for about 15 miles I have...

I am in the middle of building me a motor dont laugh but so far I have a 2.5 lt bored over 30 and am about halfway done with a major port job on my head, I would have never guessed there is about a 1/2 of extra metel on the intake ports that you can get rid of just to make it flush with the...

has anyone installed one of these in there jeep if so how much of a pain in the a$$ was it they say about 2 hours with common hand tools and is for experenced home mechs. I consider my self experenced but my patience is poor I am the type of person that will grab a hammer and make it fit. and...

well finally finished my lift after 2 weeks a couple of phone calls to 4 wheel drive hardware and ups, and now I am going to replace whats left of the 1991 tie rods has anyone fliped them meaning putting the ontop of the steering knuckles instead of underneath, I am going to buy the entire...

Has anyone with a 4 banger yj ever put tj motor mounts on their jeep, I am looking for some for urathane ones that are stiffer than the rubber ones I have now, but I can only find them for 97 and newer so I was woundering if it woud work or is it way off, kinda sucks they dont make them for the...

hey thanks folks, I am still waiting on the ups man to bring my shocks and transfer skid plate spacers, i went ahead and wound up torching the track bar off, seems rust should come in a tube it so much better than locktite.

looks great! The accessory circuitt is before the starting circuitt, and when you say does nothing is the igition switch good? or if you want to bypass the acc. part jump the starter silinoid with a wrench thats the best way to break down the two circuits since its a 80 model it will have a...

If anyone live in the hampton roads Va area I am looking for some folks to wheel and a place to wheel as it is current I have to drive about an hour away to have fun so its kind of a damper and no one ever wants to go i also go down to outerbanks and do a little beach driving so let me know. Marc

Rear trac bar to keep or not to keep I just did a 4in and thats really pushing it even with the pinon adusters you still need to run a transfercase lowering kit

I just put a 4in lift on my yj, and I am a running into a whole lot of head aches and bloody knuckles, I have a Jks teloscopping trac in the front so its not a huge prob, since I didnt buy the kit just the springs trying to save a buck (bad mistake) now my rear track bar is about an 1 1/2 to...

Hard Top Parts I have a jks track bar disco on my 91 wrangler, and I must say unless you have the sway bar disco's its kinda of a waste of time, and requires drilling to mount the bottom of the trac bar to the axle housing, they recomend welding the top mount in but it comes with a crush...

I can tell you that my four banger has 164,000 is constantly abused and runs fine sure it has blow by and the oil pressure drops some under extreme load but i wish I had a six unless they would make on rams 1/4 mile longer so I can get up do a decent speed :D owell if it was perfect then it...

I went ahead and bought an 89 yj for parts today and it has some real nice stuff and some real bad rust anyway it seems to have 2in. lift springs and skyjacker shocks, I dont know if it had skidplate spacers sice the transmission was held in with a strap only thing left of the skid is where the...

clutch hose to master cylinder is big $$$$$ I have got a yj hub bearing brand new, i bought it for a 91 but I am assumeing that it will fit any yj make me an offer I dont remember how much I payed but I think it was around 150.00 but not sure thanks Marc rooxter@msn.com I am located in...

put a supercharger on it, it will cost alot less than doing a whole drive train swap on it, i was reading somwhere that they put a supercharger, and a inerta ring on the flywheel and compaired it to the 4.0 plus it would be be cool, check out jackson racing and Paxton I think both manufactures...

I did the 3in and I must admit it look pretty rough but it works and it only to about 3hrs would have been less if my buddy werent envolved but that is what made it fun but, you can see way too much frame but I guess you get what you pay for, a 3in suspension lift is way more than a 140.00...

I must start by saying wow its been a while since I have been on the site I remember having 3 stars and around 200 post and now I am back to the begining but I like what yall have done to the place real fancy, anyway Here is my question since I am finally back home for a while and have some...

got a brand new nation brand hub bearing in the box cost around 250.00 new and has a life time guarantee from autozone have receipt. let ke know rooxter@aol.com

if it is a four cylinder i wouldnt just hack off the cat, you need the back pressure to help build horsepower, trust me I did same thing (hack off the cat) ran for about a month and presto 2 burnt valves, it may have just been my luck, but it has a cat on it now and now problems since. also i...

1045284 there was a recall on my jeep a 91 there is a feul desending unit gasket that breaks that cause the unit to ground out i got it fixed and then my gage started working better but not always great so its worth a shot marc[addsig]