Search results

1041986 Ok folks thanks for the help. Now the question is are these parts ok or should they be upgraded. Mostly road driving , occasionally offroad. [addsig]

1042411 Thanks jeepr i will look into this [addsig]

1043136 I will disagree with you ShyD33 on the wheel sizes. Ive been this stuff all my life and you can run 33s on an 8in wheel with no problems and a 35 on 10in. Not starting anything but just trying to help out a guy with the right sizes.[addsig]

1043302 Ok next question. Where do u get them at?[addsig]

1043406 Try replacing the control module first. Only about 19.00 at Auto Zone. Its located on my 87 on the drivers side inner fender under the windshield washer bucket. Every Jeep owner I know carries a spare even me. Hope this helps out.[addsig]

1054279 I took the trac bars off and their not on now. How could they cause the steering wheel to wobble while im driving.[addsig]

1054303 Ok ill get the dropped pitman arm and see how that works out. Tug for your answer i did not buy anything yet but 3 new u-bolts and the new spring perches. I fabbed my own trans case lowering bracket and just re bent my brake lines and re-screwed them to the frame. The driveshafts even...

1054343 A trailer place called trailer wheel and frame.[addsig]

1054411 JEEPSTER go SOA I just did mine this weekend and it only cost me for the spring perches and the tubing for the trans lowering brackets. Im fabricating lower shock mounts so I will still use the regular shocks. I took my brake lines loose and rebent them so their fine. My front shaft is...

1054415 The ones I used were only 1 3/4 in wide they work just fine. The driverside i think it is has to use a narrow one cause of the differential.[addsig]

1054550 So far so good. Going to make shock brackets this weekend and get them on.[addsig]

1072163 steelerman how much for lift without shocks shipped to Humble Tx 77338 ?[addsig]

1072682 Ok guys thanks for some valuable info. In a last ditch effort, this evening im going to put a t-stat back in it and get a temp sending unit and give it a whirl. [addsig]

1072741 Yes the fan shroud is still on it. And yes I did get the reverse rotation clutch, mine has the serpentene belt on it. Next is where is the Temp sending unit located on the block. The one I thought was it is not it. Im going to try a manual gauge and see if anything changes. Thanks for...

1072744 Also 1 other thing, What temperature are some of yalls Jeeps with a 258 running?[addsig]

1072775 MORGSTER thanks 4 the info. I found it right where u said. I didnt get a chance to do it this afternoon but will pick one up in the morning and let yall know how it does . Thanks again for all the help so far. [addsig]

1074051 I just went thru the same problems. After a new radiator, a new fan clutch, a new water pump, a new temp sending switch in the head, I found out the gauge was a pile of junk. I replaced it with a new aftermarket mechanical one and my temp is a buck 50 to a bock 70. AAAWWW is nice to be...

1070033 There aint a thing wrong with a B/L. I got a 3 in on my 87YJ and have not had a problem. I built bumpers front and rear to hide the small gaps. I have an automatic with air conditioner and the kit comes with brackets for the radiator to lower it and the condensor is ok. I think the kit...

1070569 I put a used set of 33-12.50-15 on my Jeep this weekend for fitment to see how much lift I need, and I used my 8in. wheels. I will have to say when I get the new 33s I will use these wheels, they look pretty good. [addsig]

1041938 How can I tell which transcase I have. And front and rear diff also. I have an 87YJ 6cyl with auto transmission. What do I look for. Thanks[addsig]