Search results

set of green 93 1/2 doors in good condition with mirrors 93 used softtop in great condition with frame stainless steel CJ mirrors low back CJ seats. some tears in seat but not too bad with slider and risers still need to figure out pricing (will post asap) located outside of cleveland ohio...

the lines not clogged i checked that first, i just didn't state it well. the only thing i can think of is at the connector that goes into the washer pump.... i get voltage on the purple colored wire when i turn the wiper switch AND when i hook the pump straight up to the battery terminals with...

i am not getting any fluid to wash my windshield. tested pump by hooking wires to battery...the pump ran fine and squirted fluid out of hose. test for voltage at connector that goes to pump... i got battery voltage everytime i twisted the turn signal lever to mist. this was on the violet...

90 yj 2.5L pretty much stock my belts are horribly squeeking. but they only really squeek when my headlights are on and i come to a stop. upon stopping my voltmeter drops to 8-9 the lights dim a little and the belt roar. when i start to move forward they squeel then go back to normal. if i turn...

i've got a 80 cj7 w/ 258 thats been sitting for years (in all weather). i am planning on popping in a used engine as soon as i can find one. what problems might i face trying to get this running? i'm sure the brakes are rusted and stuff like that. what about the transmission, tcase,...? do i...

1044370 i just had a new remaned engine but in so i am sure that all the manifold bolts and everything are tight. the motor is not working because i no longer hear it retract when i shut off the motor. i'll try and find a cheap one somewhere and install it and see what happens. [addsig]

1044836 first of all you'll have to get a wiring schematic drawing from a manual. or it is possible to use a mulitmeter or test light and test what wires get power when the transmission is put into reverse. after the wires are located it would be as simple as using a crimping tool with some...

1044837 first of all you'll have to get a wiring schematic drawing from a manual. or it is possible to use a mulitmeter or test light and test what wires get power when the transmission is put into reverse. after the wires are located it would be as simple as using a crimping tool with some...

1044838 any other takers? need some tips on installation of idle speed actuator / motor. don't want to ruin it upon installation. [addsig]

1044860 curious... what is the function of the relay? i know i installed one with some driving lamps i added to my jeep before but never bothered to look into why you need one? anyone got a simple explaination? [addsig]

1045146 put the new ISA in and it definetly works better than the old one. the only problem is it was not fully extended when i installed it. it holds a steady 750ish rpms. upon startup though i'm not getting enough to kick over cause the plunger on the ISA isn't extended enough. the manual...

1045345 i'll try cleaning the gauge and changing the sending unit this weekend and see what happens. thanks for the ideas! [addsig]

1049669 just wondering though.... do you think its the gauge itself or the sending unit? like i said it wasn't always like this. i think my '80 cj7 gauge even works better! it seems smooth until i reach that 1/2 tank full point[addsig]

1051509 the 4wd plastic hose harnesses are about $30 at the dealerships [addsig]

1044300 my 90 yj 2.5L TBI wont drop rpms after warming up. it seems that the idle speed motor is not moving, it doesnt move when shutting the motor off either. where is a good place to get a replacement? how much are they? if i try to clean it, what do i need to do so i dont ruin it more...

1045058 i've been having trouble with my idle speed actuator/motor (ISA) on my 90 yj 2.5L TBI. it wasn't extending and retracting properly to control the idle. i took it apart and it was all gummed up with dirt and oil, so i cleaned it all up and installed it. now the idle will not drop upon...

1045278 i need to replace my oil pressure sending unit or my gauge in my 90 yj. i just put a new 2.5L engine in and the gauge is still acting wild. what should be the approx. PSI for a new 2.5L at idle and driving? the factory manual says to check voltage at connector on the sending unit...

1045346 getting a cold breeze right over my shins and feet! looked under the dash and see a vent located right by where the steering column exits/enters the firewall. what position on the heater controls controls this flap vent? my cables are broke on so i have been manually moving the...

1049598 got a 90 yj 2.5L 5 speed i broke one of the metal nipples on the axle shift motor (on my dana 33 front axle) where the plastic vacuum tubes connect. this is for engaging the front axle for 4wd. i might attempt to take it off and retap a fitting into it but... if i replace the...

1049599 just wondering if anyone else seen this problem.. 90 yj 2.5L 5speed it seems lately that my gas gauge acts normal until it reaches a 1/2 tank. after i hit 1/2 on the gauge the gas seems to decrease more rapidly. i had a new sending unit put in 2 months ago and even the old one did...