Search results

46, Been told I don't look it or act it. Don't know if thats a insult or a compliment, anyhow its just a number as long as your young at heart. Frank

I had to do the same thing to my gals 93 wrangler when we put on 31x10.5 tires due to the back spacing. The tire would hit the leaf spring when the steering wheel was fully turned. I guess I was lucky because the bolt/nut assemblies came right off. Try some PB Blaser, WD-40 or perhaps apply some...

Hey Nimisus, Did ya ever figure out the deal with your bushing/insert problem or did ya drill em out? I lived in Austin for 5 years but moved to Raleigh 2 years ago when everyone was laying off. I sure do miss that city and friends Frank

you may want to look at all your metal insert/bushings, the bolts that mount the springs to the shackles are smaller than the ones that that go to the spring housing. chances are you have a larger diameter metal insert on the shackle. there are two different inner diameter inserts, before you...

I just installed a 3 inch rough country lift on my gals 93 yj. The only problem I ran into was the axle locator pins on the rear springs were .050" larger than the origional so I removed them and turned down in lieu of drilling a larger diameter hole in the axle plate. I also felt the...

I sent (or at least I think I've sent ) $25 for Jhiggins flower arrangement-fund. I am not too computer literate so please let me know if you have recieved the funds otherwise I will attemp to resend the funds again via Paypal. Thanks, Frank (pghpenna)

Perhaps I'm worrying about nothing, Just going by what they said at Jiffy Lube the last few times I had them change it. The reason I started to do it myself is they over tightened the drain/fill plug and stripped it out. They put a lil larger diameter plug instead of retapping the pan and seems...

Jet Black"

I put the 3" rough country lift on my gals 93 wrangler with only one problem. The axle locating pins in the leaf springs were .050" over the origional so I opted to remove the pins and turn them down instead of drilling a larger hole in the axle. All is fine, no vibration etc but felt the...

I'll be installing a 3 inch rough country lift on my gals 93 yj this weekend and have two questions. I know you guys said it a million times but, could you all tell me the name of the bolt loosener spray (kb blaster????). Second, I have access to air tools and all I need to do is swallow my...

1065928 Hope not, I just replaced the starter and soleniod 3 months ago[addsig]

1066387 I haven't heard the noise yet because it wasn't happening all the time, However my gal said it happened every time she tried to start the jeep today. I recently replaced the starter/and solenoid and last week I installed a new battery. If I had to take a guess I would think relay or...

1067159 I think I'll go with Jeep Addicts advice before I start with the timing/coil check. The jeep runs like a top when running, no misses at idle or acceleration. It's just a little tough to get out of bed (started) Thanks, Frank[addsig]

1067453 When the key is turned to the start position nothing happens, no turning of motor etc. All the lights/accessories are receiving power and functioning properly. after a few times of trying to start it seems as if I get enough juice to start the engine. This problem does not happen all...

1071939 Hey Steelerman, Are you origionally from the Burg or just another die hard Steeler fan? Frank[addsig]

1072328 Scott, Yes, it only happens in first gear and not all of the time.[addsig]

1047109 Hey, Anyone out there know the exact location of the manual transmission drain and filler plugs? I have a cheap Chiltons or similar type book that states it is located on the passenger side towards the top of the transmission housing. Are they the square recessed (for ratchet extention)...

1047172 My girlfriends 93 Jeep Wrangler 6 cylinder 5 speed manual transmission is grinding gears when up/down shifting. I just move her to NC from Fla and thought her baby was in shock (not used to the cold weather) because this problem just started since the move. I thought I would try to add...

1060403 Well I fixed the oil cap leak by installing a new cap (seemed simple enough), However in the process I now have a half dozen leaks coming from the valve cover gasket. Is this engine under that much pressure to make these leaks happen? I was told there is no PCV valve on my girl friends...

1061464 Got under the hood this weekend to replace the valve cover gasket which was spewing more oil than the Exxon Valdez. After springing for the gasket, permatex and a 6 pack of my favorite refreshment I was ready to roll up the sleeves and turn some wrenches. All went well and my Gals YJ...