Search results

ditto, you got a short somewhere in the dash/tail light circuit. my money would go on the corrosion

i figure that if the offset is 0, on a 7"rim, the backspace would be 3.5. i think. anyways the outside face of the tires is flush with the stock flares. also the back sits quite a bit higher than the front. i guess between 1/2" to an 1". does anyone know if the rear springs will settle...

well, i went back outside and stuck my head all around. i can see that i have 4 O2 sensors. i may have a fifth, because there are areas of the manifold i cannot see.

no tailights and 10 amp fuse blows well, i checking out the FSM and they refer to O2 bank 1 sensor 1+2+3 and bank 2 sensor 1+2. so i figured there would be 4 also. the computer said that 1/1,1/2,2/1, and 2/2 are what is giving the error for heater circuit failures i also found a list...

went to autozone today and had the guy hook the computer. it was all 4 oxygen sensors. dont know what could have set that off. had him reset it and it hasnt come back on yet.

my engine light came on today. i got code 2.5 can anyone tell me what it means??

RE discos dont use bushings, and the brackets dont use washers either. the only washers were for the bottom bolt and the bolt that goes through the swaybar. i dont recall the bolt that goes though the swaybar being too small. maybe a little play, but i think i would have noticed if it was...

surco rack was a bit over $200.00 w/ mounts & shipping. after that it was a few buck in nuts, washers, and threaded rod.

the offset is 0 on the 767's and yes they are bfg 31's. the CJ....it needs a cam. i have everyhting i need to do the cam. but i dont want to pull the motor, so i am planning on taking off the front clip. i want to devote a whole weekend to it and you know.

well, finished the lift and got my wheels. still waiting on a SYE and driveshaft http://www.imagestation.com/album/?id=4285997759&congratulation_page=Y

wont the electronic correction take care of the shift points as well? i thought i would need one but i dont really notice the transmission shifting at odd times.

ok, i was waiting til i got the tires on. i will take some pics tommorow. so i'm gonna take out the drop. i ordered a SYE + driveshaft. they will be here next thursday. the vibes are to a minimum, but the shaft binds pretty good.

i went with a 3/4" drop. helped a little, but i havent shimmed the axle yet. i'm gonna get some 2 dergree shims today. hopefully that will do the trick. i'll take some pics later. and post them under a new topic, i just called my tire shop and they messed up the order an i wont have them til...

thanks, i am ordering the shims tonight. im gonna figure out a TCL kit before i get the shims, hopefully. i acutally just finished the lift. the vibes arent too bad. they stop ata bout 35 MPH. which wont make the commute too bad, and thankfully i dont gotta get on the highway. i wont...

if you want skip channel 28 is the best.

Will these fit a '91 YJ? what year are th flares for....if they are post '97 i want em

its a '00. i dont plan on going more than 1" and the shims will definitely be steel. if it needs more than that, i'll do an SYE. thanx bounty

so where are you gonna run the wires?? i am planning on some lights and will run into the same problem in the future. my cb cable i just snuck throught the liftgate jamb and along the trim to the front, but i dont think i would want to do that for the lights.

thanks for the offer siminsez, i'll be here all day if you wanna swing by. i know i'll need some help to bleed the brakes, but laura will be back in a few hours if you cant make it.

thanks for the input, im do the lift and see whether its bad or not, i'll probably go with a 2 degree shim to start. does anyone know if i can stack shims??