Search results

1040509 well ironically your right most are metric and so are the ones on your dana 30 providing you have a stock front I think its 36 mm or something. Its available at pep boys unfortunately not available at my autozone. [addsig]

1040517 is this a manual "cj/yj " transfer case or a tj one? [addsig]

1040549 Well did you try justa straight rebuild of your carb it could easily be the front gas line fitting into your carb got knock by something or vibrated loose causing the viton needle to seat improperly and your float level to be wrong. I would recommended rebuilding it all together, or...

1040590 are you sure its a two peice i was almost sure its a one peice and 4.2 carbed jeeps "77-90" are two peice. nothing is worse then having the wrong part. Well either way you'll know when you look at it, and to answer your questioin if it is two peice like 4.2s you should be able to i've...

1040005 what size tires do you want what are you going to use it for? mud bogging, trail rides, look cool? needs a bit more info [addsig]

1040009 Well you can go with a 2" spacer lift for your springs and new shocks that would allow for 32 inch tires though there might be slight rubbing and keep a standard ride from the factory, if your not wanting to put big bucks in right now this is the best option, you can find them from 180...

1040011 auto or manual? [addsig]

1040027 where in mass are u located? [addsig]

1040068 yeah you can use a metal cover the only problem is you need to realize is that the cover will not fit pewrfectly on pre 81 jeep with 258's the passenger side is wavy as opposed to the straihgt edge thats on 81 thru 86 clyinder heads so in order to put one on you need top use a thick...

1040086 Personnally I use a sun pro 2 tach from Autozone.com, but if you really what to get them a nice one i would get one of the stock ones that mounts in the dash next to the steering wheel. YOu can get these in most online catalogs like www.4wd.com www.quadratec.com. And look for the stock...

1040105 did you try replacing or testing the clutch interlock switch for it? if the switch is stuck in the on position the cruise control will never work because it walways thinks the pedal is down the same type of thing happened to my brake switch in my camry so my brake lights were onand...

1040137 yeazh its probally your carbs flooding itself because of the steep angle, of course is this a steep oh shit kinda hill or a regular type of hill. and jumping isnt good but who cares. I jump my jeep off anything that stand s still long enough for me to drive on it. [addsig]

1040158 I'm pretty sure its nothing as serious as your whole engine is going most likely its just thje carb, mine did alot a couple years back and i had it rebiult for 30 bucks and it was perfect for years, what happens on alot of them is they wont idle do to the fact the ventruris tubes getr...

1040188 well heres my two cents it might be that your electric choke isnt functioning due to a intermittent contact with the oil temp sender on the passenger side of the engine it happened to me and what would happen is it would run fine until it came disconnected and would run right until the...

1040196 well the fastest i go in my jeep is around 83mph with 273 gears and 31's i am in fourth gear then fifth is useless unless i regear my axles. [addsig]

1040265 yes you can get itoff the internet my friend at umass got it for me and but it on video cd so we could watch it on my dvd player it wasnt the greatest quality, but if you wanted to see it before everyone else that was the way to do it. It is a good movie much better then phantom...

1040266 What you might look at is your pressure relief valve thats located in the oil filter asssembly the oil filter screws into if is stuck you can eoither get too much or too little pressure.. [addsig]

1040268 it sounds like the the clutch fork is rattling i once had a similar problem all i did was adjust my clutch linkage. so mainly i thinkl its your clutch fork. [addsig]

1040270 Well I did do the nutter bypass and there was slight improvement for low end torque , by the way I do have some pictures of the bypass. The problem was i didn't like the way it rode as much by having the vacuum advance come from the ported vacuum, becauseanytime i let off the gas ported...

1040274 yeah i think it is fairly easy and they do sell a warn kit to do it but it costs around 600 or 700 bucks i think I could be wrong I have cj, anywa I wouldn't be too concerned with about it and if you think its dragging your front end that much replace the hub bearings. your best bet is...